<?xml version="1.0" encoding="UTF-8" ?>
<rss version="2.0" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:wikidot="http://www.wikidot.com/rss-namespace">

	<channel>
		<title>nothing is working for me.</title>
		<link>https://www.contraptor.org/forum/t-513745/nothing-is-working-for-me</link>
		<description>Posts in the discussion thread &quot;nothing is working for me.&quot; - arduino uno does nothing after uploading sketch
using grbl or 3 stepper sketch from instructables.com 2 of 3 steppers stall</description>
				<copyright></copyright>
		<lastBuildDate>Fri, 06 Nov 2026 18:59:33 +0000</lastBuildDate>
		
					<item>
				<guid>http://www.contraptor.org/forum/t-513745#post-1497374</guid>
				<title>Re: nothing is working for me.</title>
				<link>https://www.contraptor.org/forum/t-513745/nothing-is-working-for-me#post-1497374</link>
				<description></description>
				<pubDate>Tue, 03 Jul 2012 07:37:13 +0000</pubDate>
				<wikidot:authorName>Albanetc</wikidot:authorName>				<wikidot:authorUserId>381022</wikidot:authorUserId>				<content:encoded>
					<![CDATA[
						 <p>Also, try pulling up the limit/endstops pins (or ground them if they're not inverting) - this may also be the reason nothing moves.</p> 
				 	]]>
				</content:encoded>							</item>
					<item>
				<guid>http://www.contraptor.org/forum/t-513745#post-1497278</guid>
				<title>Re: nothing is working for me.</title>
				<link>https://www.contraptor.org/forum/t-513745/nothing-is-working-for-me#post-1497278</link>
				<description></description>
				<pubDate>Tue, 03 Jul 2012 04:28:05 +0000</pubDate>
				<wikidot:authorName>brute4x4</wikidot:authorName>				<wikidot:authorUserId>1390629</wikidot:authorUserId>				<content:encoded>
					<![CDATA[
						 <p>ill have to try it again when i get back to work but when i uploaded the sketch to the arduino there wasn't any errors. i would sent it commands and if i remember right i was getting &quot;ok&quot; back but no movement. so i grabbed my multimeter and tested the enable pin and sent a command like x20 but i wasnt getting any response from the arduino so i tried to invert the pin and still nothing.</p> <p>im not sure which software it was but it was the newest one called reprap_new_firmware.</p> <p>the one thing i dont think i tried was inverting the limit pins.</p> 
				 	]]>
				</content:encoded>							</item>
					<item>
				<guid>http://www.contraptor.org/forum/t-513745#post-1495421</guid>
				<title>Re: nothing is working for me.</title>
				<link>https://www.contraptor.org/forum/t-513745/nothing-is-working-for-me#post-1495421</link>
				<description></description>
				<pubDate>Sun, 01 Jul 2012 04:01:14 +0000</pubDate>
				<wikidot:authorName>Albanetc</wikidot:authorName>				<wikidot:authorUserId>381022</wikidot:authorUserId>				<content:encoded>
					<![CDATA[
						 <p>Can you provide a bit more information? When you say it doesn't respond to the sketch, does it mean that you're not getting &quot;ok&quot; response back to your commands? If you are getting &quot;ok&quot; back but nothing is moving/happening, can you list your pinout from _init.pde? I'm not sure about grbl, but it also sounds like a pin assignment issue.</p> 
				 	]]>
				</content:encoded>							</item>
					<item>
				<guid>http://www.contraptor.org/forum/t-513745#post-1493517</guid>
				<title>nothing is working for me.</title>
				<link>https://www.contraptor.org/forum/t-513745/nothing-is-working-for-me#post-1493517</link>
				<description></description>
				<pubDate>Fri, 29 Jun 2012 01:09:15 +0000</pubDate>
				<wikidot:authorName>brute4x4</wikidot:authorName>				<wikidot:authorUserId>1390629</wikidot:authorUserId>				<content:encoded>
					<![CDATA[
						 <p>I am completely stumped at this point. i have tried to install the reprap_new_firmware to my arduino but it doesn't respond to the sketch. a example of this is the enable pin should be high when sending a command but the pin wont change states ( i have tried this pin inverted and non inverted and still nothing.). also the direction pins dont change voltages. so basically went back to grbl after that.</p> <p>now my problem with grbl is that i can only get the 1 axis to work(or just 2 output pins to work at a time) the other 2 just stall. i have ran all 3 axis off the 2 output pins i know work and i can get all 3 steppers to move at the same time, just not individually in there assigned pins like they should&#8230;</p> <p>then i tried to use the code from instructables &quot;how to wire a 3 axis cnc&quot; and now i can get 2 of the 3 steppers to move but the 3rd one stalls&#8230; i tried to reassign the 2 pins that didnt work to two other ones but with the same result 2 out of the 3 working.. once again if i put the stalled stepper signal pins on the output pins on a working one i can get all 3 to spin.</p> <p>so i know its not a power supply issue, not a stepper drivers issue, and not a stepper motor issue&#8230;..</p> <p>any help would be greatly appreciate and i mean ANY help! lol</p> <p>almost forgot to add im using:<br /> arduino uno ATmega328 and or a arduino mega 2560<br /> 3 big easy drivers from spark fun, in single step mode 2A per phase<br /> 3&#160;400 step steppers spark fun 3.3v 1.7A per phase<br /> atx power supply, i think 300watt 14A 12V</p> 
				 	]]>
				</content:encoded>							</item>
				</channel>
</rss>