Flickr
gatonero_ posted a video:
My first Gcode circle! :-D. The pen is a little bit moving, everything else worked perfectly :-)
gatonero_ posted a video:
With
G20
G91
G3 X0 Y0 I1 J0 F10
not a perfect circle as I expected, more like two separates curves, but much better than I expected today!
Flights of Ideas posted a photo:
![Contraptor Mini-CNC [electronics]](http://farm3.static.flickr.com/2774/4401586590_a87c5234b9_m.jpg)
Flights of Ideas posted a photo:
![Contraptor Mini-CNC [front left]](http://farm3.static.flickr.com/2772/4401586598_dfd3895e39_m.jpg)
Flights of Ideas posted a photo:
![Contraptor Mini-CNC [above]](http://farm3.static.flickr.com/2491/4401586580_ff40ea268a_m.jpg)
uxfeeds (UXfeeds):
Contraptor: http://url4.eu/1hLwS
lucasgonzalez (lucasgonzalez):
RT @gatonero: My Contraptor Mini-CNC made the first Gcode circles http://bit.ly/bPSFNu :-D
contraptor (Contraptor Project):
RT @gatonero: My Contraptor Mini-CNC made the first Gcode circles http://bit.ly/bPSFNu :-D
gatonero (Christoph):
My Contraptor Mini-CNC made the first Gcode circles http://bit.ly/bPSFNu :-D
Youtube
 |
First run of all three axis.
|
From: gatoneroyt
Views: 120
 1 ratings
|
| Time: 00:53 | More in Science & Technology |
 |
Z axis is running! :-D Just a view noises, which are originated in mixing some metric with US imperial parts, This metric parts from a common hardware store don't fit exactly. Tomorrow I will present the first running Contraptor Mini CNC outside USA! www.contraptor.org
|
From: gatoneroyt
Views: 11
1 ratings
|
| Time: 00:50 | More in Science & Technology |
 |
Much better with flywheels, reduced vibrations and noises. The click cklack in one high speed direction is from my metric susbstitution on the shaft mount, it doesn't fit 100%.
|
From: gatoneroyt
Views: 13
1 ratings
|
| Time: 00:59 | More in Science & Technology |
 |
Hard job with just three US imperial tools. I had to integrate the first metric screw ;-), because I ruined a shaft mounts tap while adjusting. Some vibrations somewhere, maybe a loose screw. Will check it tomorrow. Now I'm very glad to get this run.
|
From: gatoneroyt
Views: 10
1 ratings
|
| Time: 00:54 | More in Science & Technology |
 |
Mini CNC is making UHMWPE pads for Contraptor kits Contraptor is an open design project to create inexpensive DIY Cartesian robot construction set www.contraptor.org
|
From: albanetcsr
Views: 52
 0 ratings
|
| Time: 00:59 | More in Howto & Style |
 |
This is my first test running the Y axis of my becoming Contraptor Mini CNC. Runs like a charme :-D www.contraptor.org
|
From: gatoneroyt
Views: 42
2 ratings
|
| Time: 01:34 | More in Science & Technology |
 |
Testing XY table assembled from Contraptor set. Contraptor is an open design project to create inexpensive DIY Cartesian robot construction set www.contraptor.org
|
From: albanetcsr
Views: 1629
0 ratings
|
| Time: 00:20 | More in Howto & Style |
 |
XY plotter assembled from Contraptor set -test pattern Contraptor is an open design project to create inexpensive DIY Cartesian robot construction set www.contraptor.org
|
From: albanetcsr
Views: 1899
0 ratings
|
| Time: 00:51 | More in Howto & Style |
 |
This contraption was assembled from the Contraptor set to drill 16x16=256 holes per square inch in 8"x10" area of the cutting mat with 1/32" drill bit (~20000 holes total). The job was done in about 6 hours Contraptor is an open design project to create inexpensive DIY Cartesian robot construction set www.contraptor.org
|
From: albanetcsr
Views: 1843
0 ratings
|
| Time: 01:14 | More in Howto & Style |
 |
Mini-router drawing test at 16x. Y axis stalled at 4:19 Contraptor is an open design project to create inexpensive DIY Cartesian robot construction set www.garagefab.cc
|
From: albanetcsr
Views: 2738
1 ratings
|
| Time: 04:23 | More in Howto & Style |
